Aprilaire 8570 Specifikace stáhnout pdf (Strana 23)

7. INPUT DEALER CONTACT INFORMATION

During thermostat operation, the two multi-function buttons

are labeled INFO and MENU. When the INFO button is

pressed, the thermostat will display the humidity and

temperature sensed by the ADHC (if an ADHC has been

installed), then the thermostat will display any monitor

messages and dealer contact information. At installation,

the contact information is blank and only the thermostat

model number appears. You have the option of inputting this

contact information with the name and number of your

company. Three twenty (20) character lines are available for

your company name and contact info.

To change the contact information:

1. Make sure the thermostat is in the OFF mode.

2. Press and hold both the ▲ and ▼ buttons for 3 seconds.

– The display will show the ADV. SETTINGS MENU.

3. Use the ▲ or ▼ button to highlight “INPUT DEALER INFO”

and press the SELECT button. This enters Line 1.

4. To cancel, press the BACK button. This returns to the

ADV. SETTINGS MENU. You must be at the first position

when pressing the BACK button to return to the

ADV. SETTINGS MENU.

5. To go back a character, press the BACK button.

6. To enter a character, use the ▲ or ▼ buttons to scroll

through the available characters. Press the SELECT button

to enter the character.

7. To finish Line 1 and go to Line 2, repeatedly press

SELECT, filling all remaining characters with spaces,

then press SELECT again.

8. Repeat to fill Line 2 and Line 3.

9. To finish, press the SELECT button after entering the

20th character of the third line.

- 41 -- 40 -

6. BALANCE POINTS (HEAT PUMPS ONLY)

This feature is only available when the thermostat has been

configured to operate heat pumps (see SET THE

CONFIGURATION DIP SWITCHES on page 6) and only when an

outdoor temperature is available to the thermostat. Outdoor

temperature can come from an ADHC or from an outdoor

temperature sensor.

The low balance point is the outdoor temperature at or below

which the thermostat will lockout the compressor(s) – only

auxiliary heat will be used to satisfy heating demands. The high

balance point is the outdoor temperature at or above which the

thermostat will lockout the auxiliary heat – only compressor

heat will be used to satisfy heating demands. Emergency heat

operation is unaffected by the high balance point.

To change the balance points:

1. Make sure the thermostat is in the OFF mode.

2. Press and hold both the ▲ and ▼ buttons for 3 seconds.

– The display will show the ADV. SETTINGS MENU.

3. Use the ▲ or ▼ button to highlight “SET BALANCE

POINTS” and press the SELECT button.

4. To cancel, press the BACK button. This will return you to

the ADV. SETTINGS MENU.

5. To change the low balance point, press the ▲ or ▼

button to raise or lower the temperature value

(range is -10°F to 35°F and OFF).

6. To change the high balance point, press the SELECT

button, then press the ▲ or ▼ button to raise or lower the

temperature value (range is 40°F to 80°F and OFF).

7. To finish and return to the ADV. SETTINGS MENU, press

the SELECT button after the value(s) have been set.

Important time saver: If the thermostat is installed as part

of a Model 6504 Intelligent Zoned Comfort System, the

balance points only need to be changed at one thermostat.

The Model 6504 will share the new settings with all

connected thermostats.

1 2 ... 18 19 20 21 22 23 24 25

Komentáře k této Příručce

Žádné komentáře

Aprilaire 8570 Specifikace Strana 23

Komentáře k této Příručce

Související produkty a manuály pro Termostaty Aprilaire 8570